Product features
Factory speakers can leave voices difficult to follow and bass short of weight. This Soundtech package brings together the listed components for Ford Ranger PX2/PX3 Speaker DSP Amplified Package Basic sound (handle). Choose by the chassis and installed sound system, not the badge alone.
What this upgrade addresses
- A defined component list, so speakers, wiring and mounting parts can be planned together.
- Replacement speakers for the positions described in the package, without treating a similar looking driver as interchangeable.
- DSP adjustment for level, crossover and time alignment where supported by the listed processor. Professional setup is needed to suit the car.
Component specifications
HELIX Ci3 K165.2FM-S3 MK2
| Specification | Value |
|---|---|
| Power handling RMS | 100 Watts |
| Maximum power handling | 150 Watts |
| Frequency response | 60 Hz to 25,000 Hz |
| Impedance | Z | 3 Ω |
| Sensitivity | SPL | 92 dB @ 2.83V / 1m 88 dB @ 1W / 1m |
| Outer diameter | ø | Tweeter: 32.0 mm / 1.26” Midbass: 165.0 mm / 6.50” |
| Installation diameter | ø | Tweeter: 32.0 mm / 1.26” Midbass: 142.0 mm / 5.59” |
| Installation depth | Tweeter: 9.8 mm / 0.39” Midbass: 60.7 mm / 2.39” |
| Dimensions crossover | 103.3 x 50.4 x 25.0 mm / 4.07 x 1.98 x 0.98” |
| Impedance | Z | 3 Ω |
| DC resistance | Re | 3.0 Ω |
| Resonance frequency | Fs | 70 Hz |
| Mechanical Q factor | Qms | 4.17 |
| Electrical Q factor | Qes | 1.05 |
| Total Q factor | Qts | 0.84 |
| Compliance | Cms | 454 μm/N |
| Equivalent air volume | Vas | 11.2 L |
| Force factor | B*l | 4.0 Tm |
| Cone area | Sd | 133 cm 2 |
| Moving mass | Mms | 11.3 g |
| Mechanical resistance | Rms | 1.18 kg/s |
| Voice coil diameter | ø | 25 mm |
| Voice coil winding height | 10.5 mm |
| Max. linear excursion | Xmax | +/- 3.2 mm |
| Impedance | Z | 4 Ω |
| Resonance frequency | Fs | 1800 Hz |
| Voice coil diameter | ø | 20 mm |
| Tweeter | Ultra compact, aluminum dome, neodymium magnet and FlexMount20 |
| Midbass | Paper with Cenosphere coating, ProConnect terminal and FlexMount165 |
| Crossover | Tweeter: 12 dB highpass, protection and level adjustment Midbass: 6 dB lowpass |
Tweeter: 32.0 mm / 1.26” Midbass: 165.0 mm / 6.50”
Tweeter: 32.0 mm / 1.26” Midbass: 142.0 mm / 5.59”
Tweeter: 9.8 mm / 0.39” Midbass: 60.7 mm / 2.39”
103.3 x 50.4 x 25.0 mm / 4.07 x 1.98 x 0.98”
Voice coil winding height
Ultra compact, aluminum dome, neodymium magnet and FlexMount20
Paper with Cenosphere coating, ProConnect terminal and FlexMount165
Tweeter: 12 dB highpass, protection and level adjustment Midbass: 6 dB lowpass
HELIX Ci3 C165.2FM-S3 MK2
| Specification | Value |
|---|---|
| Power handling RMS | 100 Watts |
| Maximum power handling | 150 Watts |
| Frequency response | 60 Hz to 25,000 Hz |
| Impedance | Z | 3 Ω |
| Sensitivity | SPL | 92 dB @ 2.83V / 1m 88 dB @ 1W / 1m |
| Outer diameter | ø | 165.0 mm / 6.50” |
| Installation diameter | ø | 142.0 mm / 5.59” |
| Installation depth | 60.7 mm / 2.39” |
| Impedance | Z | 3 Ω |
| DC resistance | Re | 3.1 Ω |
| Resonance frequency | Fs | 72 Hz |
| Mechanical Q factor | Qms | 4.02 |
| Electrical Q factor | Qes | 1.04 |
| Total Q factor | Qts | 0.82 |
| Compliance | Cms | 466 μm/N |
| Equivalent air volume | Vas | 11.5 L |
| Force factor | B*l | 3.8 Tm |
| Cone area | Sd | 133 cm 2 |
| Moving mass | Mms | 10.4 g |
| Mechanical resistance | Rms | 1.17 kg/s |
| Voice coil diameter | ø | 25 mm |
| Voice coil winding height | 10.5 mm |
| Max. linear excursion | Xmax | +/- 3.2 mm |
| Voice coil diameter | ø | 20 mm |
| Tweeter | Aluminum dome and neodymium magnet |
| Midbass | Paper with Cenosphere coating, ProConnect terminal and FlexMount165 |
| Crossover | Integrated, 6 dB highpass |
Voice coil winding height
Paper with Cenosphere coating, ProConnect terminal and FlexMount165
MATCH UP 4DSP
| Specification | Value |
|---|---|
| @ 4 Ohms | Channels A to B: 2 x 60 Watts (min. 3 Ohms) |
| @ 2 Ohms | Not specified |
| @ 1 Ohm | Not specified |
| bridged @ 4 Ohms | Not specified |
| bridged @ 2 Ohms | Not specified |
| Subwoofer output @ 4 Ohms | Kanal C to D: 2 x 85 Watts |
| Subwoofer output @ 2 Ohms | Kanal C to D: 2 x 140 Watts |
| Amplifier technology | Class GD |
| Inputs | 4 x Highlevel speaker input 1 x Optical SPDIF (12 to 96 kHz) |
| Input sensitivity | 2.8 to 11 Volts |
| Input impedance RCA / Cinch | Not specified |
| Input impedance highlevel | 9 to 33 Ohms with ADEP.3 |
| Outputs | 4 x Speaker output 1 x RCA / Cinch 1 x Remote Out |
| Output voltage RCA / Cinch | 3 Volts RMS |
| Frequency response | 15 Hz to 22,000 Hz |
| DSP resolution | 64 Bit |
| DSP power | 295 MHz (1.2 billion MAC operations/second) |
| Sampling rate | 48 kHz |
| DSP type | Audio signal processor |
| Signal converters | A/D: BurrBrown D/A: BurrBrown |
| Signal to noise ratio digital input | 102 dB (A weighted) |
| Signal to noise ratio analog input | 101 dB (A weighted) |
| Distortion (THD @ 1 kHz, 1 W into 4 Ohms) | < 0.03 % |
| Distortion (THD+N @ 1 kHz, 1 W into 4 Ohms) | < 0.03 % |
| Damping factor | > 50 |
| Operating voltage | 10.5 to 18 Volts (max. 5 sec. down to 6 Volts) |
| Power rating | DC 12 V ⎓ 35 A max. |
| Idle current | 260 mA |
| Max. remote output current | 500 mA |
| Operating temperature range | −40° C to +70° C |
| Fuse | 1 x 30 A LP-Mini fuse (APS) |
| Additional features | Class GD technology with dynamically controlled power supply, 32 Bit CoProcessor, ADEP.3 circuit, Start Stop capability, Smart Control Port, USB-C, Auto Remote switch, Line Out |
| Dimensions (H x W x D) | 46 x 130 x 110 mm / 1.81 x 5.12 x 4.33" |
CFMK165 FOR.1
HELIX FlexMount CFMK165 to 6.5" 3D Printed Speaker Adapter | Pair: CFMK165 FOR.1 Ford
CFMK20 FOR.1
PP-AC 74
PP-ISO 5
| Specification | Value |
|---|---|
| Cable harness length | 5.00 meters |
| Connections | 1 x 20 pole MOLEX connector 2 x ISO male connector (chamber A and B) 2 x ISO female connector (chamber A and B) |
AERPRO APS21
AERPRO APS21 Speaker plug adaptors to suit Ford & Mazda
Fitment and exclusions
| Specification | Value |
|---|---|
| Distributor application | Ford Ranger PX2/PX3 |
| Required factory sound system | Basic sound (handle) |
| Amplifier integration | No factory amplifier to new amplifier integration |
Not for Burmester, Bose, Harman Kardon or another factory amplified system unless it is explicitly the system named in this package.
What is in the box
| Package quantity | Item and selected model |
|---|---|
| 1 | HELIX Ci3 K165.2FM-S3 MK2 to 6.5" 2-Way Component Speaker Set, FlexMount | 3Ω |
| 1 | HELIX Ci3 C165.2FM-S3 MK2 to 6.5" 2-Way Coaxial Speaker Pair, FlexMount | 3Ω |
| 1 | MATCH UP 4DSP to 4 Channel PnP Amplifier | 5ch DSP |
| 2 | HELIX FlexMount CFMK165 to 6.5" 3D Printed Speaker Adapter | Pair: CFMK165 FOR.1 Ford |
| 1 | HELIX FlexMount CFMK20 to 1" 3D Printed Speaker Adapter | Pair: CFMK20 FOR.1 Ford |
| 1 | MATCH PP-AC 00 to 98 Car Radio To Amplifier T-Harness ver.1 | ISO: PP-AC 74 Ford from 2010 (24 Pin) |
| 1 | MATCH PP-ISO Molex To ISO Harness: PP-ISO 5 to 5m |
| 2 | AERPRO APS21 Speaker plug adaptors to suit Ford & Mazda |
Installation and setup
Professional installation is recommended. Check the vehicle build, factory amplifier, connectors and mounting positions before work starts. Minor modifications may be needed depending on the exact year and trim. Installation and tuning are not included in the package price. Where a DSP amplifier is listed, set the crossovers, levels and routing for the actual speakers and test music, calls, navigation prompts and warning sounds.
Warranty
Australian Consumer Law rights apply. Confirm the warranty for the selected components when arranging the installation.
Frequently asked questions
Which components are included?
HELIX Ci3 K165.2FM-S3 MK2 (quantity 1), HELIX Ci3 C165.2FM-S3 MK2 (quantity 1), MATCH UP 4DSP (quantity 1). The package table lists the remaining selected items and quantities.
Which vehicle and factory system is this for?
Use the exact distributor application and selected component models shown above. The vehicle build, body and installed factory audio equipment must be checked together.
How does the amplifier connect?
Soundtech specifies adding the listed amplifier to a vehicle without a factory amplifier. Match the listed radio harness to the actual factory connections.
Does this package need DSP tuning?
Yes. The supplied MATCH UP 4DSP needs channel routing, crossovers and levels set for the selected speakers and the vehicle. Arrange professional setup.
Are installation and tuning included?
No. The price covers the listed products. Installation and any DSP tuning are arranged separately. Minor modifications may be needed depending on the exact year and trim.
What should be checked before replacing the speakers?
Check the stated impedance, installation depth, cutout and connectors for HELIX Ci3 K165.2FM-S3 MK2. Use the selected adapters where listed. A nominal speaker diameter or a similar grille is not enough to establish fitment.
Recommended for You
- Choosing a selection results in a full page refresh.
!