Product features
If voices sound thin or bass becomes hard to follow, check the speakers and the way the factory system drives them. This Soundtech package brings together the listed speakers and integration parts for the Audi Q7 4M. Match the factory sound option before choosing the kit.
What this upgrade addresses
- A defined component list, so speakers, wiring and mounting parts can be planned together.
- Replacement speakers for the positions described in the package, without treating a similar looking driver as interchangeable.
- DSP adjustment for level, crossover and time alignment where supported by the listed processor. Professional setup is needed to suit the car.
Component specifications
Ci3 K200.2FM-S3 MK2
| Specification | Value |
|---|---|
| Power handling RMS | 100 Watts |
| Maximum power handling | 150 Watts |
| Frequency response | 50 Hz to 25,000 Hz |
| Impedance | Z | 3 Ω |
| Sensitivity | SPL | 94 dB @ 2.83V / 1m 90 dB @ 1W / 1m |
| Outer diameter | ø | Tweeter: 32.0 mm / 1.26” Woofer: 195.0 mm / 7.68” Woofer with universal mounting ring: 208.9 mm / 8.22" |
| Installation diameter | ø | Tweeter: 32.0 mm / 1.26” Woofer: 173.5 mm / 6.83” |
| Installation depth | Tweeter: 9.8 mm / 0.39” Woofer: 63.7 mm / 2.51” |
| Dimensions crossover | 103.3 x 50.4 x 25.0 mm / 4.07 x 1.98 x 0.98” |
| Impedance | Z | 3 Ω |
| DC resistance | Re | 3.0 Ω |
| Resonance frequency | Fs | 67 Hz |
| Mechanical Q factor | Qms | 4.25 |
| Electrical Q factor | Qes | 0.93 |
| Total Q factor | Qts | 0.76 |
| Compliance | Cms | 300 μm/N |
| Equivalent air volume | Vas | 19.0 L |
| Force factor | B*l | 5.1 Tm |
| Cone area | Sd | 214 cm 2 |
| Moving mass | Mms | 18.8 g |
| Mechanical resistance | Rms | 1.87 kg/s |
| Voice coil diameter | ø | 25 mm |
| Voice coil winding height | 11.6 mm |
| Max. linear excursion | Xmax | +/- 3.8 mm |
| Impedance | Z | 4 Ω |
| Resonance frequency | Fs | 1800 Hz |
| Voice coil diameter | ø | 20 mm |
| Tweeter | Ultra compact, aluminium dome, neodymium magnet and FlexMount20 |
| Woofer | Paper with Cenosphere coating, ProConnect terminal, FlexMount200 and grille |
| Crossover | Tweeter: 12 dB highpass, protection and level adjustment |
Tweeter: 32.0 mm / 1.26” Woofer: 195.0 mm / 7.68” Woofer with universal mounting ring: 208.9 mm / 8.22"
Tweeter: 32.0 mm / 1.26” Woofer: 173.5 mm / 6.83”
Ci3 K165.2FM-S3 MK2
| Specification | Value |
|---|---|
| Power handling RMS | 100 Watts |
| Maximum power handling | 150 Watts |
| Frequency response | 60 Hz to 25,000 Hz |
| Impedance | Z | 3 Ω |
| Sensitivity | SPL | 92 dB @ 2.83V / 1m 88 dB @ 1W / 1m |
| Outer diameter | ø | Tweeter: 32.0 mm / 1.26” Midbass: 165.0 mm / 6.50” |
| Installation diameter | ø | Tweeter: 32.0 mm / 1.26” Midbass: 142.0 mm / 5.59” |
| Installation depth | Tweeter: 9.8 mm / 0.39” Midbass: 60.7 mm / 2.39” |
| Dimensions crossover | 103.3 x 50.4 x 25.0 mm / 4.07 x 1.98 x 0.98” |
| Impedance | Z | 3 Ω |
| DC resistance | Re | 3.0 Ω |
| Resonance frequency | Fs | 70 Hz |
| Mechanical Q factor | Qms | 4.17 |
| Electrical Q factor | Qes | 1.05 |
| Total Q factor | Qts | 0.84 |
| Compliance | Cms | 454 μm/N |
| Equivalent air volume | Vas | 11.2 L |
| Force factor | B*l | 4.0 Tm |
| Cone area | Sd | 133 cm 2 |
| Moving mass | Mms | 11.3 g |
| Mechanical resistance | Rms | 1.18 kg/s |
| Voice coil diameter | ø | 25 mm |
| Voice coil winding height | 10.5 mm |
| Max. linear excursion | Xmax | +/- 3.2 mm |
| Impedance | Z | 4 Ω |
| Resonance frequency | Fs | 1800 Hz |
| Voice coil diameter | ø | 20 mm |
| Tweeter | Ultra compact, aluminium dome, neodymium magnet and FlexMount20 |
| Midbass | Paper with Cenosphere coating, ProConnect terminal and FlexMount165 |
| Crossover | Tweeter: 12 dB highpass, protection and level adjustment Midbass: 6 dB lowpass |
Tweeter: 32.0 mm / 1.26” Midbass: 165.0 mm / 6.50”
Tweeter: 32.0 mm / 1.26” Midbass: 142.0 mm / 5.59”
MATCH UP 6DSP MK2
| Specification | Value |
|---|---|
| Power RMS ≤ 1% THD+N | |
| @ 4 Ohms | Channels A to D: 65 Watts (min. 3 Ohms*) Channels E to F: 75 Watts (min. 3 Ohms*) |
| @ 2 Ohms | Channels E to F: 125 Watts |
| @ 1 Ohm | |
| bridged @ 4 Ohms | |
| bridged @ 2 Ohms | |
| Max. output power per channel** | Channels A to D: up to 80 Watts RMS @ 4 Ohms Channels E to F: up to 90 Watts RMS @ 4 Ohms Channels E to F: up to 160 Watts RMS @ 2 Ohms |
| Amplifier technology | Class GD |
| Inputs | 6 x Highlevel speaker input 1 x Optical SPDIF (12 to 96 kHz) 1 x Extension Card 2.0 |
| Input sensitivity | 2.8 to 11 Volts |
| Input impedance RCA / Cinch | |
| Input impedance highlevel | 9 to 33 Ohms with ADEP.3 |
| Outputs | 6 x Speaker output 1 x RCA / Cinch 1 x Remote Out |
| Output voltage RCA / Cinch | 3 Volts RMS |
| Frequency response | 15 Hz to 22,000 Hz |
| DSP resolution | 64 Bit |
| DSP power | 295 MHz (1.2 billion MAC operations/second) |
| Sampling rate | 48 kHz |
| DSP type | Audio signal processor |
| Signal converters | A/D: BurrBrown D/A: BurrBrown |
| Signal to noise ratio digital input | 104 dB (A weighted) |
| Signal to noise ratio analog input | 100 dB (A weighted) |
| Distortion (THD @ 1 kHz, 1 W into 4 Ohms) | < 0.015 % |
| Distortion (THD+N @ 1 kHz, 1 W into 4 Ohms) | < 0.02 % |
| Distortion (THD @ 100 Hz, 1 W into 4 Ohms) | |
| Distortion (THD+N @ 100 Hz, 1 W into 4 Ohms) | |
| Operating voltage | 10.5 to 18 Volts (max. 5 sec. down to 6 Volts) |
| Power rating | DC 12 V ⎓ 35 A max. |
| Idle current | 360 mA |
| Max. remote output current | 500 mA |
| Operating temperature range | −40° C to +70° C |
| Fuse | 1 x 30 A LP-Mini fuse (APS) |
| Additional features | Class GD technology with dynamically controlled power supply, 32 Bit CoProcessor, ADEP.3 circuit, Start Stop capability, Smart Control Port, USB-C, Auto Remote switch |
| Dimensions (H x W x D) | 46 x 130 x 130 mm / 1.81 x 5.12 x 5.12" |
* DC resistance min. 3.0 Ohms ** In typical multi channel applications
PP-VAG 2.6
| Specification | Value |
|---|---|
| Cable harness length | 2.00 meters |
| Connections | 1 x 8 pole MOLEX female connector for connecting a MATCH Plug & Play subwoofer 1 x 20 pole MOLEX male connector for connection to the system connector input of the amplifier 1 x 4 pole MOLEX male connector for connection to the highlevel input E + F of the amplifier* 1 x 8 pole MOLEX male connector for connection to the speaker output E , H of the amplifier 1 x Quadlock male connector for connection to the OEM head unit 1 x Quadlock female connector for connection to the original cable harness |
* Depending on the installed OEM sound system the output channels E + F of the OEM head unit either provides the highlevel signals of the front woofers (front left and front right) or of the center speaker and subwoofer.
CWK TES1.T-225TC
| Specification | Value |
|---|---|
| Cable harness length | 0.225 Meters / 0.7 feet |
| Connections | 1 x Tesla specific plug 1 x COMPOSE tweeter plug |
ZRS-AG 24
ZRS-AG 24
CFMK200 AUD.4
CFMK200 AUD.4
CFMK165 AUD.3
CFMK165 AUD.3
CFMK25 AUD.1
CFMK25 AUD.4
Fitment and exclusions
| Fitment | Requirement |
|---|---|
| Vehicle | Audi Q7 |
| Chassis and body | 4M SUV |
| Build range | 2015 to 2019, before facelift, 4M chassis only |
| Required factory sound system | Audi Sound System |
Only the stated generation, body and factory sound system are included. Other chassis, body styles and audio options are excluded. Match the original amplifier and connections before installation.
Not for the 2019 facelift or later versions under this verified application range. Check the build and original audio equipment, not registration year alone.
Not for Bose or Bang and Olufsen factory audio. The stated factory system and matching original connections are required.
What is in the box
| Package quantity | Item and selected model |
|---|---|
| 1 | Ci3 K200.2FM-S3 MK2 |
| 1 | Ci3 K165.2FM-S3 MK2 |
| 1 | MATCH UP 6DSP MK2 |
| 1 | PP-VAG 2.6 |
| 2 | CWK TES1.T-225TC |
| 2 | ZRS-AG 24 |
| 1 | CFMK200 AUD.4 |
| 1 | CFMK165 AUD.3 |
| 1 | CFMK25 AUD.1 |
| 1 | CFMK25 AUD.4 |
Installation and setup
Professional installation is recommended. Check the vehicle build, factory amplifier, connectors and mounting positions before work starts. Minor modifications may be needed depending on the exact year and trim. Installation and tuning are not included in the package price. Where a DSP amplifier is listed, set the crossovers, levels and routing for the actual speakers and test music, calls, navigation prompts and warning sounds.
Warranty
Australian Consumer Law rights apply. Confirm the warranty for the selected components when arranging the installation.
Frequently asked questions
Which components are included?
Ci3 K200.2FM-S3 MK2 (quantity 1), Ci3 K165.2FM-S3 MK2 (quantity 1), MATCH UP 6DSP MK2 (quantity 1). The package table lists the remaining selected items and quantities.
Which vehicle and factory system is this for?
Audi Q7 4M SUV, 2015 to 2019, before facelift, 4M chassis only. Required factory system: Audi Sound System. Other chassis, bodies and factory systems are not included.
How does the amplifier connect?
Use the exact interface and harness models in the component table. The installer must confirm the signal path and retained vehicle functions.
Does this package need DSP tuning?
Yes. The supplied MATCH UP 6DSP MK2 needs channel routing, crossovers and levels set for the selected speakers and the vehicle. Arrange professional setup.
Are installation and tuning included?
No. The price covers the listed products. Installation and any DSP tuning are arranged separately. Minor modifications may be needed depending on the exact year and trim.
What should be checked before replacing the speakers?
Check the stated impedance, installation depth, cutout and connectors for Ci3 K200.2FM-S3 MK2. Use the selected adapters where listed. A nominal speaker diameter or a similar grille is not enough to establish fitment.
Recommended for You
- Choosing a selection results in a full page refresh.
!